72201 Jet Pump 1.5hp 2 speed

In stock
Add to Wish List
In stock

Add to wishlist
72201 Jet Pump 1.5hp 2 speed
72201 Jet Pump 1.5hp 2 speed

1.5 Hp, 115 VAC, 60 Hz, 2 Sp, XP2

The jet pump provides water pressure for the hydrotherapy system by recirculating water from the spa, drawing it through the skimmer and filtration system, and forcing the water through the fixed jets, rotary jets and jetstream. These pumps are designed for the presence of water at all times.

The opening at the bottom of the door is a vent for the heat generated by the operation of the jet pump. The vent will eliminate the problem of overheating pump motors and protect the other components from excessive heat. It is important that the vent opening be kept clear at all times. If the vent opening becomes obstructed, overheating of the jet pump may occur.

72201 Jet Pump 1.5hp 2 speed is for the following models:

Make Model Date Range
Hot Spot SX 2011-Current
Hot Spot SLXtra 2001-2002
Hot Spot Sprint 2010-2011
Hot Spot Dash 2010-2011
Hot Spot Tobago 2003-2005
Hot Spot Trinidad 2003-2005
Solana SX 2006-2010
Solana TX 2006-2010
Solana RX 2006-2009
Caldera Aventine 2010-2015
Caldera Cumberland 2002-2009
Caldera Cascade 2000-2003
Caldera Tarino 2013-Current
Caldera Cima 2010-2011
Caldera Lina 2010-2011
Caldera San Gabriel 2008
Caldera Oasis 2001-2007


  • 2.5 HP, 2 SP, 230V, 60 HZ, 11 AMP (High Speed)
  • 2.5 HP, 2 SP, 230V, 60 HZ, 3.3 AMP (LowSpeed) 
  1. Disconnect power to the spa.
  2. Access the equipment compartment.
  3. Drain the spa.
  4. Disconnect the the jet pump from the control box.
  5. Remove the copper bonding wire from the bonding lug on the jet pump motor.
    Drain the pump by removing bleedline from the drain barbfitting or plug.
  6. Turn the jet pump unions counterclockwise on the intake and discharge of the jet pump to disconnect them from the plumbing.
    Note: Make sure to save the union o-rings.
  7. Remove the mounting bolt(s) securing the jet pump to the equipment compartment floor.
  8. Remove the jet pump from the equipment compartment.
  9. To reinstall the jet pump, reverse steps 1 to 9.
    Important: Make sure that the jet pump union o-rings are properly seated when re-tightening the unions.


Item No.  Part No. Description 
1 71415 Manifold XP Manetek
2 ** Motor, mag, 48fr, 1.5 hp, 8.0/16.0a, 230/115v
3 71036 Fitting, compress 2" w/o-ring
4 71693 Volute 48fr xp2
5 71447 Seal, xp
6 71404/na Impeller 1.5 hp, xp
7 71409 Wear ring, xp
8 71554 O-ring, volute
9 71696 Cover, suction xp2
10 32267 Drain plug, pump
11 72344 Kit, cal, pump hose duct
12 017066 Mount, rubber-pump
13 72462 Cord assy, pump 14/3, 60" straight yr2002
14 71413 Screw, 8-32 x 5/8, (xp volute)
15 34447 O-ring, compress fitting 2"
16 71594 O-ring, drain
* 72992 Pump, 1.5 hp, 230v 60 hz, 1 spd, xp2 (2")
© 2023 Hot Tub Spa Supplies


eCommerce Design by DotcomWeavers