35911 Wall Fitting Drain

$3.83
In stock
SKU
35911
Add to Wish List
In stock

Add to wishlist
35911 Wall Fitting Drain
35911 Wall Fitting Drain

Wall fitting for rear drain.

The drain system consists of a drain opening in the footwell. The drain valve located in the equipment compartment controls the drain.

Draining the spa

  1. Disconnect power from the spa. If a 115 volt model is being drained, unplug the GFCI and place the GFCI and the cord in an elevated position to prevent water from entering the GFCI.
  2. Access the equipment compartment.
  3. Remove the drain cap from the drain.
  4. Vent the spa cover by folding it in half or opening it entirely.
  5. Open the drain valve by turning the black knob of the drain clockwise. The spa will drain by gravitational flow. The spa should drain almost completely using the main drain.
  6. If winterizing the spa, use a cup or soft rags to remove any excess water from the spa or the equipment compartment.
  7. Additionally, leave the drain partially open to allow any water that gets into the spa to drain.
  8. Close the drain valve by turning the black knob counterclockwise.
  9. Reinstall the drain cap onto the main drain.
  10. Refill spa.
  11. Connect power to the spa.
  12. Removal
    1. Disconnect power to the spa.
    2. Drain the spa.
    3. Access the equipment compartment.
    4. Locate the drain in the equipment compartment.
    5. Remove the drain cap.
    6. Remove the Phillips Head screw from the top of the drain handle.
    7. Remove the drain handle.
    8. Tip the spa upside down or onto its side.
    9. Locate the drain opening in the wood toe-kick. The drain is located directly behind this wood.
    10. Beginning at this spot, remove foam until the drain valve is exposed.
      NOTE: Be sure to remove enough foam so the drain valve can be cut from the plumbing.
    11. Cut plumbing lines on each side of the drain valve as close as possible.
    12. Lift the drain valve straight up to remove it. Discard the drain valve.
    13. Remove the threaded section of plumbing from the opening in the toe-kick.
    14. Using a coupler and a small length of hose, couple the drain valve to the remaining plumbing.
      NOTE: Be sure the drain valve is located so the valve stem can be accessed from the equipment compartment.
    15. Glue the hose adapter onto a 2-1/2" piece of 3/4" PVC pipe.
      Thread the PVC pipe end through the toe-kick and test fit it into the drain valve. The hose adapter should extend through the toe-kick far enough so a drain cap can be installed.
    16. Glue the PVC pipe and hose adapter into the drain valve.
    17. Using a foam kit, replace all the foam removed to access the drain valve.
    18. Apply the foam to seal the bottom of the spa.
     

 

Specifications

Item Description Part #
1 Drain Wallfitting 3/4 Inch 35911
2 Bleed Line Nipple 1/4 Inch 30598
3 Flex Tubing 3/4 Inch 70312
4 Bleed Line Nipple 1/4 Inch 30598
5 Adapter 70346
6 Drain Valve 30592
7 Drain Cap With Washer 30700
8 Drain Valve Adapter 3/4 Inch 30703
9 Adapter 70346
10 Drain Valve Knob 33916
11 Drain Valve Knob Screw 32784
12 Coupling 3/4 Inch 30661

Item Description Part #
1 Drain Wallfitting 3/4 Inch 35911
2 Wallfitting, Rear: Wallfitting #1 Rear 30490
3 O-ring: 0-ring 2.350inx.190in 30 Sil 30482
4a Wallfitting #1 Front 30488
4b Wallfitting, Grey W/O Knockout 71263
5a Standpipe Filter 9-3/4In 31390
5b Standpipe, W/Restrictor 76504
6 Filter, 65Sf Tri-X 9/Cs 73250
7a Standpipe,Cap 3-1/2,Hss,White 31389
7b Standpipe,Cap 3-1/2,Tr,Grey 36513

Item Description Part #
1 Cap 30700
2 Drain Valve 30592
3 Drain Adapter 3/4 30703
4 Adapter 70346
5 3/4 x 1/4 Adapter 34504
6 Tee 3/4 (SlipxSlipxSlip) 34751
7 Flex Tubing 3/4 70312
8 Wallfitting 35911
9 Drain Valve AR/VV 76072

 

Item Description Part #
1 Cap 30700
2 Hose Adapter 30703
3 PVC Pipe 3/4 x 2-1/2 L 70346
4 Drain Valve Complete 33937
5 Coupler 3/4 30661
6 Bleedline Nipple 30598
7 Flex Tubing 3/4 70312
8 Wallfitting 35911
9 Drain Handle 33916
10 Screw 32784

 

 

 

Item Description Part #
1 Wallfitting Front 30488
2 O-Ring Silicone 30482
3 Wallfitting Rear 30490
4 Wallfitting Rear Drain - 1/2" 71128
5 Wallfitting Rear Drain - 3/4" 35911
6A Coupler 3/4 30661
6B Clear Vinyl Tubing 1/2 70313
7 Flex Tubing 3/4" 70312
8 Adapter 30702
9 Drain Valve 30592
10 Drain Cap 30700
11A Heater Return Screen White 72722
11B Heater Return Screen Taupe 71886
11C Heater Return Screen Cool Gray 72723
11D Heater Return Screen Warm Gray 73296
12 Reducer Bushing 1-1/2" x 3/4" 31420
13 Elbow Street 1-1/2" x 3/4" 30650
14 Reducer Bushing 3/4"x 1/2" 30675
15 Flex Tubing 1/2" 70313
16 Barbed Adapter 1/2" 31218
17 Sprin Clamp 31228
© 2019 Hot Tub Spa Supplies

|

eCommerce Design by DotcomWeavers