34366 Screw PH PLP SS HILO

$2.24
In stock
SKU
34366
Add to Wish List
In stock

Add to wishlist
34366 Screw PH PLP SS HILO
34366 Screw PH PLP SS HILO

Screw PH PLP SS HILO

This part is a replacement 10-32" X 1/2" pan head screw for select Hot Spring hot tub models. To best meet your needs, use the screw to secure the moto-massage faceplate.

Compatible with a variety of the 1995 to current Hot Spring Highlife, Hot Spot, and Solana spa models.

*Check specs section for full list of compatible models and years.

Specifications

 

Item 

Description  Serial Numbers  Part No.
1 Facia Plate Dual Moto  KK GG JJ 1S1001 - Current  77185
2 Screw 10-16 x 3PH PLP SS Hi-lo KK GG JJ 1S1001 - Current  34366
3 Screw Cover Moto  KK GG JJ 1S1001 - Current  77241
4 Dual Moto Jet Assy  KK GG JJ 1S1001 - Current  77242
5 Air Tube w/o-ring moto -massage  KK GG JJ 1S1001 - Current  73539
6 Abrasion Cap (Air Tube )  KK GG JJ 1S1001 - Current  30723
7 O-ring Moto Air Tube  KK GG JJ 1S1001 - Current  33020
8 Dual Moto Niche Air Fitting  KK GG JJ 1S1001 - Current  73564
9 Manifold w/Arline Assembly  KK GG JJ 1S1001 - Current  73540
** Check valve  KK GG JJ 1S1001 - Current  38390

Item Description Part Number
1a Facia Plate Moto White 36079
1b Facia Plate Moto C Grey 36511
1c Facia Plate Moto W Grey 73305
2 Screw 16x3 34366
3a Screw Cover Moto White 36144
3b Scrrew Cover Moto c grey 36510
3c Screw Cover Moto w grey 73306
3d Screw Cover Taupe 71896
4 Moto Jet Assembly white 73307
5 Air Tube with o oring 70307
6 Abraision cap (air tube) 30723
7 O ring moto air tube 33020
8a Extrusion shim MM Short 36143
8b Extrusion shim MM Long 36557
* Check Valve 38390

* Non Illustrated Part

Removal
  1. Open or remove the spa cover.
  2. Using a standard blade screwdriver, remove the three faceplate screw covers.
  3. Remove the three screws securing the Moto Massage faceplate to the spa.
  4. Remove the Moto Massage faceplate.
  5. Reach into the jet recess and locate the air tube. Gently remove this tube from the barbed nipple at the back of the recess.
  6. Grasping the base of the Moto Massage (end closest to the rear of the jet recess) gently turn the entire assembly counterclockwise until it can be removed.
  7. To reinstall the Moto Massage, reverse steps 1 to 6.

Important Instructions Regarding Moto Massage Alignment: 

In order the for the Moto Massage to operate properly it is imperative that the Moto Massage nozzle be properly positioned after the assembly is tightened in the Moto niche.

To properly align, ensure that the two holes located on the nozzle face are position horizontally and that the Moto assembly travels vertically within the niche.

© 2023 Hot Tub Spa Supplies

|

eCommerce Design by DotcomWeavers