71434 Cord Replacement For Circulation Pump

$11.14
In stock
SKU
71434
Add to Wish List
In stock

Add to wishlist
71434 Cord Replacement For Circulation Pump
71434 Cord Replacement For Circulation Pump

Power cord for Circulation Pump Silentflow 5000 and E5  Sillent , used for all Hot Spring and Tiger River Spas 1997 - Current

Important note: The Silent Flo 5000 replaces all previous style circulation pumps.

The circulation pump draws water through the circulation pump filter and then pushes it past the heater, flow switch (if equipped), bleedline, ozone injector (if equipped) and back into the spa through the heater return fitting. Its function is to circulate the water through the heater for the maintenance of temperature and to provide continuous filtration (if equipped) of the spa water.

The circulation pump is water lubricated and cooled and requires the presence of water at all times. These pumps should NOT be operated without water present in the spa. If "dry run", the pump has an internal safety device (thermal cut-off) that will automatically shut down the pump should it overheat.

On spas prior to 1999, the thermal cut-off automatically resets when the pump cools down. However, on all spas starting in 1999, the thermal cut-off will only reset when power is disconnected from the spa.

 

 
  • Minimum flow for the circulation pump is 1 gallon in 30 seconds.

(back to top)

 
Removal
  1. Disconnect power to the spa.
  2. Access the equipment compartment.
  3. Unplug the circulation pump from the control box.
  4. If the spa is filled with water, clamp the circulation pump inlet and outlet tubing with Hose Clamp Pliers.
  5. Remove the bonding wire and base bracket screws.
  6. Using Spring Clamp Pliers, slide the spring clamps located on the inlet and outlet fittings back onto the vinyl tubing.
  7. Remove the vinyl tubing from the pump inlet and outlet fittings.
  8. Disconnect the electrical cord for the old pump. Take note of the electrical hookup.

CIRCULATION PUMP INSTALLATION

  1. Install the original electrical cord onto the new pump.
  2. Reverse steps 3 to 7 of the Circulation Pump Removal instructions.
  3. Check for water leaks.
  4. Reconnect power to the spa.
  5. Perform a water flow test.
  6. Check for any air in the plumbing lines. If air does not clear, bleed off the air at the closest tubing clamp.
  7. Reinstall the equipment compartment door.

ELECTRICAL WIRING INSTRUCTIONS FOR SilentFlo 5000

Refer to the following instructions to install an electrical cord / ground on a no-cord SilentFlo 5000:

  1. Remove the end cap of the new SilentFlo 5000 pump by removing the two slotted screws on the rear black panel.
  2. Insert the stripped ends of the cord through the rubber gasket on the end cap.
  3. Connect the ground wire (green) to grounding lug located on the body of the pump.
  4. The other two wires should be installed into the terminal block. The pump is not affected by the polarity of the incoming power, so either wire can be installed in either terminal. NOTE: Insure that excess wire does not protrude from the rear of the terminal block. Excessive wire will cause direct shorts.
  5. After the wires are secure, reinstall the end cap using the two slotted screws.
  6. If an exterior grounding wire exists, you must attach the exterior grounding lug with single screw (provided in kit). Then attach exterior grounding wire to exterior grounding lug.

Specifications

 

 Item  Description  Part #
 1  CIRC PUMP, E5 60HZ  74427
 2  CORD, CIRC PUMP  71434

 

 

Item Decsription Part #
1 Main Control Board 77089
2 Clamp Romex 3/4 30105
3 Plug Hole 0.3/8" 36043
4 Bushing Strain Relief 3/8" 30099
5a Cord Assy Pump 14/4 Flag 60" 72461
5b Cord Assy Pump 14/3 Flag 60" 72462
6 Strain Releif 3/8" 7K-2 30098
7 Cord Circ Pump Replacement 71434
8 Receptacle Assy Ozone 72474
9 Plug Hole 0.50" 36044
10 Thermostor Hi-Limit 72492
11 Thermistor Control 72493
* Kit Heater Board Replacemnet 74618
* Fuse Sloblo 1/2A 250V 5MM X 20MM 37089
* Program Jumper Sgunt .100 36021
* Kit Cable Assy Press Switch 72639
* Fuseholder 34506
* Fuse 2 Amp 250V 34934
* Kit 12C Comm Hub 8 Port 74150

 

 

Item Description Part #
1A Control Head Replacement 71260
1B Control Head G & S **
1C Control Head F & I **
1D Control Head H & J **
1E Control Head Replacement 71920
2A IQ-2000 Control Box 71382
2B IQ-2000 Control Box 71485
2C IQ-2000 Control Box (Canadian) 71384
2D IQ-2000 Control Box (Canadian) 71487
3 Strain Relief 10/3 36022
4 Clamp Romex 3/4 30105
5 Cord Assy GFCI 20120
6 Cord 14/3 XP Jet Pump 71416
7 Bushing Strain Releif 3/8" 30098
8 Plug Hole 0.875" 36043
9 Cord Circ Pump Replacement '97 71434
10 Receptacle Assy Ozone 72724
11 Kit HSS Lampholder '95-'00 71292
12 Plug Hole 0.50" 36044
13A Cable Assy Panel Interface 34931
13B Cable Assy Panel Interface 71755
14 Power Jumper Terminal Block 71377
15 Screw Terminal Block 71529
16 Relay 2 Pole 18VCD 74723
* Screw IQ 2000 Cover 36676
* Screw Mounting Bracket 36898
* CBA Mounting Bracket 36018
* CBA Mounting Bracket (Classic) 36019
* Fuseholder (Canada Only) 34506
* Fuse 2 Amp 250V (Canada Only) 34934
* Screw Receptacle for Control Panel 34481

 

 

 

 

Item Description Part #
1 Kit CBA Advent Orca Cal 76288
2 Kit Control Head Cal 76269
3 Clamp Romex 3/4" 30105
4 Plug Hole 0.875" 36043
5 Bushing Strain Releif 3/8" 30099
6a Kit Pump Cord 14/4 2SPD STRS 72461
6b Kit Pump Cord 14/3 1SPD STRS 72462
7 Strain Releif 3/8" 7k-2 30098
8 Cord Circ Pump 71434
9 Ozone Receptacle 72474
10 Thermistor Hi-Limit 72492
11 Thermistor Control 72493
12 Kit Heater Board Replacement 76071
13 Fuseholder 34506
14 Fuse 2 AMP 250V 34934
15 Program Jumper Shunt .100 36021
16 Kit 12C Comm Hub 8 Port 74150
17 Power Jumper 2 Pin 39192
18 Power Jumper 3 Pin 39193
© 2019 Hot Tub Spa Supplies

|

eCommerce Design by DotcomWeavers