Discontinued

*All Sales Are Final

Starite Max E Glass 1 hp single speed jet pump for pre 1993 Hot Spring models.

The jet pump provides power for the hydrotherapy system by recirculating water from the spa, drawing it through the skimmer and filtration system, and forcing the water through the fixed jets, Moto-Massage jets and Jetstream. These pumps are designed for the presence of water at all times.

The opening at the bottom of the door is a vent for the heat generated by the operation of the jet pump. The vent will eliminate the problem of overheating pump motors and protect the other components for excessive heat. It is important that vent opening be kept clear at all times. If the vent opening becomes obstructed, overheating of the jet pump may occur.

Caution: Installation of a rodent screen may increase the possibility of obstructing the vent opening with debris.

On later model spas, each jet pump is equipped with a pump shroud. The pump shroud is attached to the rear of the jet pump. This shroud is a vent for the heat generated by the operation of the jet pump motor. The shroud will eliminate the problem of overheating pump motors and protect the other components for excessive heat. It is important that the vent outlet for the pump shroud be kept clear at all times. If the pump shroud outlet vent becomes obstructed, overheating of the jet pump may occur.

16 amp/115 Volts AC or 8 amp/230 volt AC, 1 hp, 1 speed

Removal

Disconnect power to the spa.
Access the equipment compartment.
Drain the spa.
Disconnect the the jet pump from the control box.
Remove the copper bonding wire from the bonding lug on the jet pump motor.
Drain the pump by removing bleedline from the drain barbfitting or plug.
Turn the jet pump unions counterclockwise on the intake and discharge of the jet pump to disconnect them from the plumbing.
Note: Make sure to save the union o-rings.
Remove the mounting bolt(s) securing the jet pump to the equipment compartment floor.
Remove the jet pump from the equipment compartment.
To reinstall the jet pump, reverse steps 1 to 9.
Important: Make sure that the jet pump union o-rings are properly seated when re-tightening the unions.

Specifications

Item	Description	1 H.P.	2 H.P.	All Models	Plumb. Fitting
-	Pump	30215	31239
1	Seal Plate			70032
2	Impellor	30223	70120
3	O-Ring			30222
4	Freeze Drain Plug			30218
5	O-Ring			70033
6	Volute			30217
7	O-Ring			30220
8	Clamp			30219
9	Screw			70036
10	Washer			70158
11	Diffusser			30221
12	Seal Assy			30224
13	Water Slinger			70039
14	Bolt			70059
15	Pad			N/A
16	Bolt			30370
17	Washer			30413
18	Bolt			70035
19	Washer			70158
20	Mounting Bracket	70031	70126
21	Vinyl Tubing 1/4"				70318
22	Clamp 1/4"				31134
23	Pump Cord			10409
24	Nut			N/A
25	Insert			70071
26	Barbed Fitting				32267
27-31	Motor Assy	**	**
28	Capacitor Run	30228	N/A
29	Capacitor Starting	N/A	70128
30	Cover			34480
31	Points	N/A	N/A
32	Flex Tubing 1-1/2"				70309
33	O-Ring				30237
34	Adapter				31348
35	Union Kit			30548
36	O-Ring				30261
37	Adapter				30552
38	Union Kit				N/A

** Order Pump, Complete listed above

N/A Part Not Available

Questions

Serial Number Verification

30215 Jet Pump